Themabewertung:
  • 0 Bewertung(en) - 0 im Durchschnitt
  • 1
  • 2
  • 3
  • 4
  • 5
MRC - Anleitung Hülle / instruction hull
#11
Die Pilotendeck-Rückwand besteht aus 4 Hauptteilen und 2 Zusatzteilen.
Es gibt die Rückwand, die beiden Schleusen und das Verbindungsstück zum Verhüttungsturm.
Zusätzlich gibt es noch zwei Fensterrahmen.

Nach dem Ausschneiden der Teile müssen zuerst die beiden Fensterrahmen an die äußere
Rückwand innen eingeklebt werden. Man kann die beiden Fensterrahmen auch weglassen.

Wenn man die Fensterrahmen einkleben will, muss man innen die Fensterfläche und außen
das komplette Fenster ausschneiden. An die Außenwand wird der Fensterrahmen geklebt und
an die Innenand ein durchsichtiges Stück Kunststoff als Fensterscheibe.

Danach wird der Verbindungsgang zum Turm an dei Rückwand geklebt.

An die Seiten werden die Scheleusen geklebt. Und zwar zuerst nur die Flächen mit den
Schleusentüren aneinander. Trocknen lassen. Danach die Klebelasche an die äußere Rückwand.

Wenn alle Teile trocken sind, wird die gesamte Rückwand auf die vorgesehene Stelle des
Pilotendecks aufgeklebt. Die Schotts und die jeweils einzelne Schottseitenwand können zuerst
noch ohne Kleber gelassen werden, damit man das Gesamtteil besser positionieren kann.
Wenn die Rückwand klebt, können noch die Schotts angeklebt werden.

•••••

The pilot deck rear wall consists of four main parts and 2 optional parts.
There is the rear wall, two air locks and the link to the processing tower.
Aditional there are two window frames.

After cutting out the parts, the window frames has to be glued to the inside of the outer
rear wall. The window frames are optional.

For gluing in the window frames, the inner window glas and the complete outer window must
be cut out. The window frames are glued to the outer wall and a window from any clear
plastic sheet is glued to the inner wall.

Now the linking corridor to the processing tower is glued to the rear wall.

To both sides are glued the air locks. First there are glued only the surfaces with the air locks
on it back to back. Let dry. Then the glue tab to the outer rear wall.

When all parts are dry, the complete rear wall is glued to its position on the pilot deck.
The air locks should be left without glue till the rest is attached properly to the pilot deck and the
processing tower. If the rear wall is fixed the air locks and the side walls of the air locks can be
glued too.


Angehängte Dateien Thumbnail(s)
           
Bemalte Minis 2013: 39 • 2014: 23 • 2015: 58 • 2016: 44 • 2017: 104 • 2018: 5 • 2019: 122 • 2020: 140 • 2021: 52 • 2022: 231 • 2023: 49...
Zitieren


Nachrichten in diesem Thema
1.1. Pilotendeck / pilot deck - von Niceyard - 28.08.2008, 19:03
1.2. Turmdeck / tower deck - von Niceyard - 28.08.2008, 19:24
2.0. Seitenwände / hull sides - von Niceyard - 28.08.2008, 19:34
3.0 Hintere Flügel / rear wings - von Niceyard - 30.08.2008, 03:38
4.0 Pilotendeck-Rückwand / pilot deck rear wall - von Niceyard - 30.08.2008, 03:42
5.3. Treppenhaus / stair house - von Niceyard - 02.09.2008, 22:36
6.1. Luftauslässe / Air exhaust - von Niceyard - 02.09.2008, 22:47
8.0 Seitenflügel / side wings - von Niceyard - 02.09.2008, 22:54
Unterseite / Underneath - von Niceyard - 03.09.2008, 00:27
10.0. Frontseite / front - von Niceyard - 03.09.2008, 00:32
10.1. Frontseite / front - von Niceyard - 03.09.2008, 00:34
10.2. Frontseite / front - von Niceyard - 03.09.2008, 00:36
10.3. Frontseite / front - von Niceyard - 03.09.2008, 00:38
10.4. Frontseite / front - von Niceyard - 03.09.2008, 00:40
10.5. Frontseite / front - von Niceyard - 03.09.2008, 00:41
Ansichten / Impressions - von Niceyard - 03.09.2008, 00:45
Crawler Impression - von Niceyard - 05.09.2008, 02:09
14.0. rechtes Heck / right rear - von Niceyard - 05.09.2008, 02:10
14.1. rechtes Heck / right rear - von Niceyard - 05.09.2008, 02:11
14.2. Rechtes Heck / right rear - von Niceyard - 05.09.2008, 02:12
14.3 Rechtes Heck / right rear - von Niceyard - 05.09.2008, 02:14
15.0 Linkes Heck / left rear - von Niceyard - 05.09.2008, 02:17
Übersichtsbild / General look - von Niceyard - 05.09.2008, 02:35
Farbe / Colour - von Niceyard - 05.09.2008, 17:23
Status - von Niceyard - 05.09.2008, 17:49
25 Schneidlaser - Cutting laser - von Niceyard - 20.09.2008, 05:11
25 Schneidlaser - Cutting Laser - von Niceyard - 20.09.2008, 05:17

Gehe zu:


Benutzer, die gerade dieses Thema anschauen: 1 Gast/Gäste